Harley Tip Over Sensor Reset; A Must-Read Guide
You’ve probably heard of the Harley Tip Over Sensor if you’re a Harley owner. It’s an important safety feature that can detect if your bike has tipped over and trigger an automatic engine shut-off to prevent further damage.
However, once the sensor has been triggered, it needs to reset before you can ride your bike again. In this blog post, we’ll go over how to reset the Harley Tip Over Sensor and how to avoid triggering it in the first place.
What does a motorcycle tip over sensor do?
A motorcycle tip over sensor is a safety feature designed to detect if a motorcycle has fallen over or been laid down. The sensor is typically located near the battery or under the seat and can detect any sudden change in angle, acceleration, or deceleration that could indicate a tip over.
Once the sensor has been triggered, it sends a signal to the engine control unit (ECU), which shuts off the engine to prevent further damage.
This feature is essential for preventing accidents and reducing the risk of rider injury or motorcycle damage. Resetting the tip over sensor is typically required after it has been triggered, so the bike can be ridden safely.
Why would the Harley Tip Over Sensor be triggered?
The Harley Tip Over Sensor can be triggered in various situations, such as when the bike falls over or is laid down.
It’s designed to detect any sudden angle, acceleration, or deceleration change that could indicate a tip-over. This safety feature can help prevent accidents and damage to your bike.
How to Reset the Harley Tip-Over Sensor?
Resetting the Harley Tip Over Sensor is straightforward, but following the steps carefully is important to avoid any damage to your bike. Here’s a step-by-step guide to resetting the sensor:
- Turn off the motorcycle and remove the seat to access the battery.
- Locate the sensor, which is usually located near the battery.
- Disconnect the negative cable from the battery.
- Press and hold the reset button on the sensor for at least five seconds.
- Reconnect the negative cable to the battery.
- Turn on the motorcycle and check that the engine light is off.
It’s important to note that the Harley Tip Over Sensor’s exact location may vary depending on your bike’s model. Be sure to consult your owner’s manual or do additional research to locate the sensor on your specific model.
How to Avoid Triggering the Harley Tip-Over Sensor?
The best way to avoid triggering the Harley Tip Over Sensor is to practice safe riding techniques and take precautions to prevent your bike from tipping over. Here are some tips to help you avoid triggering the sensor:
- Always park your bike on level ground and use the kickstand or a sturdy motorcycle stand to keep it upright.
- Avoid parking on soft or uneven ground, which can cause your bike to tip over.
- Be cautious when making tight turns or maneuvering your bike at low speeds, as these are everyday situations where tip-overs can occur.
- Always wear appropriate protective gear, such as a helmet and riding jacket, to help prevent injuries in a tip-over.
Harley tipped over won’t start; what can I do?
If your Harley has tipped over and won’t start, there are a few things you can do to troubleshoot the issue and get your bike running again. Here are some steps you can take:
- Check for damage
After a tip over, it’s important to inspect your bike for any damage. Check for any visible signs of damage, such as dents, scratches, or broken parts. If you notice any damage, having a professional mechanic inspect your bike before attempting to start it is best.
- Reset the tip over sensor
If your bike has a tip-over sensor, it may have been triggered when your bike tipped over. In this case, you must reset the sensor before your bike can start again. Follow the steps outlined in your owner’s manual or in the previous section of this blog post to reset the sensor.
- Check the battery
If your bike won’t start, it’s possible that the battery has been drained or damaged during the tip over. Check the battery connections to make sure they are secure and clean. If the battery is dead, try jump-starting your bike or charging the battery.
- Check the fuel and spark plugs
If your bike is getting fuel and spark, it should start up. Check the fuel level and make sure your bike has enough gas. You should also inspect the spark plugs to see if they need to be replaced.
- Seek professional help
If your bike still won’t start after checking these things, it may be time to take it to a professional mechanic. They can diagnose and repair any damage to your bike and get it running again.
Remember to always wear appropriate protective gear when working on your motorcycle, and be cautious when attempting any repairs or maintenance. If you’re not comfortable working on your bike yourself, it’s best to seek the help of a professional mechanic.
Conclusion
The Harley Tip Over Sensor is an important safety feature that can help prevent accidents and damage to your bike. Following the steps outlined in this blog post, you can easily reset the sensor and get back on the road. Remember always to practice safe riding techniques and take precautions to prevent your bike from tipping over. Stay safe out there, and happy riding!
